rc:lantian-l90
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
rc:lantian-l90 [22.01.2018 22:58] vergo [Notes] |
rc:lantian-l90 [18.07.2024 01:10] (current) vergo [Videos] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ====== Lantian L90 ====== | ====== Lantian L90 ====== | ||
| - | {{ : | + | {{ : |
| ^ Specifications | ^ Specifications | ||
| Line 10: | Line 10: | ||
| | ESC | BLHELI_S V2 10A 4in1 ESC (from MyRCMart) | | | ESC | BLHELI_S V2 10A 4in1 ESC (from MyRCMart) | | ||
| | Motors | Racerstar Racing Edition 1103 BR1103B 8000KV | | | Motors | Racerstar Racing Edition 1103 BR1103B 8000KV | | ||
| - | | Props | Kingkong 1935 3-Blade Bullnose | | + | | Props | <del>Kingkong 1935 3-Blade Bullnose</ |
| - | | Receiver | FS-RX2A Pro | | + | | Receiver | <del>FS-RX2A Pro</ |
| - | | Camera | 600TVL 1/4 1.8mm CMOS FPV 170 Degree Wide Angle Lens (from Banggood) | | + | | Camera | <del>600TVL 1/4 1.8mm CMOS FPV 170 Degree Wide Angle Lens (from Banggood)</ |
| | VTX | Eachine VTX03 | | | VTX | Eachine VTX03 | | ||
| + | | Antenna | < | ||
| | Battery | Turnigy nano-tech 2S1P 460 mAh 25-40C | | | Battery | Turnigy nano-tech 2S1P 460 mAh 25-40C | | ||
| ^ ^^ | ^ ^^ | ||
| - | | Weight | 57 g\\ 88 g (with 2S1P 460 mAh battery) | | + | | Weight | <del>57 g</ |
| | M2M | 9 cm | | | M2M | 9 cm | | ||
| | Flight time | 4-5 minutes | | | Flight time | 4-5 minutes | | ||
| + | |||
| + | ===== Videos ===== | ||
| + | |||
| + | * https:// | ||
| + | * https:// | ||
| + | * https:// | ||
| + | * https:// | ||
| + | * https:// | ||
| + | * https:// | ||
| + | * https:// | ||
| ===== Notes ===== | ===== Notes ===== | ||
| - Edges of frame pieces should be sanded to avoid wear in wiring | - Edges of frame pieces should be sanded to avoid wear in wiring | ||
| - | - Camera has been mounted with rubber O-rings due to lack of better mount | + | - <del>Camera has been mounted with rubber O-rings due to lack of better mount</ |
| - Receiver antenna has been reinforced with a cable tie + heat shrink | - Receiver antenna has been reinforced with a cable tie + heat shrink | ||
| - Don't attempt to flash the ESC firmware, 1 of 4 is likely to fail if done via FC, however changing settings is ok | - Don't attempt to flash the ESC firmware, 1 of 4 is likely to fail if done via FC, however changing settings is ok | ||
| - | - The camera | + | - The original |
| - Remove the microphone from the camera, you don't need it | - Remove the microphone from the camera, you don't need it | ||
| - Replace nylon standoffs with aluminium standoffs for extra durability | - Replace nylon standoffs with aluminium standoffs for extra durability | ||
| * The provided M2 screws are however good and long enough | * The provided M2 screws are however good and long enough | ||
| + | - Older Kingkong 1935 props have a much tighter center hole which may not always fit the motors and push the shaft out of the motor instead when the prop is inserted | ||
| + | * More recent Kingkong 1935 props fix this issue with a slightly larger center hole, those can be identified from the center hub which isn't any longer fully flat | ||
| + | - RunCam Micro Swift 2 will not fit with the default standoffs with the included mount | ||
| + | * With some plastic removal, it's possible to fit the camera using a custom mount while still using the default standoffs and having possibility to get some angle to the camera | ||
| + | * Only the height is a restricting factor | ||
| + | - FrSky XM replaced with FrSky XM+ due to [[https:// | ||
| + | * The issues were likely caused by the TX being so close to the VTX and taking interference from it | ||
| + | * FS-RX2A Pro didn't have this issue | ||
| ===== Wiring ===== | ===== Wiring ===== | ||
rc/lantian-l90.1516654701.txt.gz · Last modified: 22.01.2018 22:58 by vergo
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
