rc:realacc-martian-iv-3-inch
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
rc:realacc-martian-iv-3-inch [11.08.2019 22:31] vergo |
rc:realacc-martian-iv-3-inch [29.07.2024 03:30] (current) vergo |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ~~NOTOC~~ | ~~NOTOC~~ | ||
| + | |||
| + | <note important> | ||
| ====== Martian IV (3 inch) ====== | ====== Martian IV (3 inch) ====== | ||
| + | |||
| + | {{ : | ||
| ^ Specifications | ^ Specifications | ||
| | Frame | Realacc Martian IV (3 inch) | | | Frame | Realacc Martian IV (3 inch) | | ||
| - | | FC+ESC | HGLRC F4 Zeus | | + | | FC+ESC | HGLRC F4 Zeus AIO 15A | |
| - | | Motors | RCX H1407 3200KV | + | | Motors | RCX H1304 5000KV |
| - | | Props | HQProp T3x3x3\\ Emax Avan 3x2.4x3 | | + | | Props | <del>HQProp T3x3x3</ |
| - | | Receiver | FrSky R-XSR | | + | | Receiver | <del>FrSky R-XSR</ |
| | Camera | RunCam Robin with 1.8 mm lens | | | Camera | RunCam Robin with 1.8 mm lens | | ||
| | DVR | RunCam Mini FPV DVR Module | | | DVR | RunCam Mini FPV DVR Module | | ||
| Line 28: | Line 32: | ||
| - ESC didn't have issues with firmware flashing, came with old firmware that doesn' | - ESC didn't have issues with firmware flashing, came with old firmware that doesn' | ||
| - FC is essentially 3S max | - FC is essentially 3S max | ||
| - | - The cap included | + | - The FC bundle provided |
| - | - Configuring F.Port with the FC didn't for some reason succeed in providing two way communication resulting in lack of telemetry, RSSI however gets transmitted and shown in OSD | + | - Configuring F.Port with the FC didn't for some reason succeed in providing two way communication resulting in lack of telemetry, RSSI however gets transmitted and shown in OSD (FrSky R-XSR specific) |
| - Power wire needed to be longer than usual due to the short wires used in the Tattu batteries | - Power wire needed to be longer than usual due to the short wires used in the Tattu batteries | ||
| - For power wire management, it's better to have the battery strapped with wires facing forward | - For power wire management, it's better to have the battery strapped with wires facing forward | ||
| Line 52: | Line 56: | ||
| ===== Wiring ===== | ===== Wiring ===== | ||
| - | {{: | + | {{: |
| * BB from FC connector (white wire) is for buzzer | * BB from FC connector (white wire) is for buzzer | ||
| * S6 from FC connector (yellow wire) is DVR control | * S6 from FC connector (yellow wire) is DVR control | ||
| - | * TX6 from FC is used for VTX SmartAudio | + | * TX3 from FC is used for VTX SmartAudio |
| + | * TX6 from FC is used for the receiver | ||
| * Dual ground wiring in DVR is needed to reduce signal noise | * Dual ground wiring in DVR is needed to reduce signal noise | ||
| * The FC connector is in reality in the top end of the FC but has been marked in the image on the side for clarity, unused wires can be removed | * The FC connector is in reality in the top end of the FC but has been marked in the image on the side for clarity, unused wires can be removed | ||
| * The shown wiring result in the OSD being visible in the video recorded by the DVR | * The shown wiring result in the OSD being visible in the video recorded by the DVR | ||
rc/realacc-martian-iv-3-inch.1565551913.txt.gz · Last modified: 11.08.2019 22:31 by vergo
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
