This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
rc:blackout-super-mini-h-quad [21.06.2015 21:12] vergo |
rc:blackout-super-mini-h-quad [12.06.2016 17:04] (current) vergo |
||
---|---|---|---|
Line 1: | Line 1: | ||
~~NOTOC~~ | ~~NOTOC~~ | ||
- | |||
- | {{ : | ||
====== Blackout Super Mini H Quad ====== | ====== Blackout Super Mini H Quad ====== | ||
+ | |||
+ | {{ : | ||
^ Specifications | ^ Specifications | ||
Line 9: | Line 9: | ||
| FC | Naze32 (Acro), rev 5 | | | FC | Naze32 (Acro), rev 5 | | ||
| Motor | Cobra 2204 2300KV x 4 | | | Motor | Cobra 2204 2300KV x 4 | | ||
- | | ESC | KISS ESC 12A x 4 | | + | | ESC | <del>KISS ESC 12A</ |
| BEC | Pololu D24V10F5, 5V 1A | | | BEC | Pololu D24V10F5, 5V 1A | | ||
| OSD | Micro MinimOSD | | | OSD | Micro MinimOSD | | ||
- | | Prop | GemFan 5x3 x 4 | | + | | Prop | <del>GemFan 5x3 (ABS) x 4</ |
| Receiver | FrSky TFR4-B | | | Receiver | FrSky TFR4-B | | ||
| Camera | RunCam 600TVL Mini with 2.8mm lens\\ Mobius with standard lens | | | Camera | RunCam 600TVL Mini with 2.8mm lens\\ Mobius with standard lens | | ||
Line 31: | Line 31: | ||
* https:// | * https:// | ||
* https:// | * https:// | ||
- | * https:// | + | * https:// |
+ | * https:// | ||
===== Notes ===== | ===== Notes ===== | ||
Line 40: | Line 42: | ||
- use bright colored propellers when flying with others to provide better visibility even with fpv | - use bright colored propellers when flying with others to provide better visibility even with fpv | ||
- UART2 (RC3/RC4 pins) needs to be used with OSD serial communication since UART1 (marked RX/TX pins) is shared with the USB port which will not work if OSD is connected to it and powered at the same time | - UART2 (RC3/RC4 pins) needs to be used with OSD serial communication since UART1 (marked RX/TX pins) is shared with the USB port which will not work if OSD is connected to it and powered at the same time | ||
+ | - the vibration damping of the included camera mount is practically non existent, using 80 gram vibration damping balls instead provides a much better result without requiring every propeller to be in perfect balance all the time | ||
+ | |||
+ | ===== PID settings (from older setup) ===== | ||
+ | |||
+ | 3S, 2300KV, GemFan 5x3, 6" compatible motor arms, KISS ESCa (oneshot not enabled) | ||
+ | |||
+ | ^ ^ P ^ I ^ D ^ | ||
+ | | roll | 4.0 | 0.030 | 20 | | ||
+ | | pitch | 4.4 | 0.035 | 22 | | ||
+ | | yaw | 8.5 | 0.045 | 0 | | ||
+ | |||
+ | ^ rc rate ^ rc expo ^ roll rate ^ pitch rate ^ yaw rate ^ | ||
+ | | 1.30 | 0.60 | 0.35 | 0.35 | 0.55 | | ||
+ | |||
+ | Cleanflight 1.8.1. PID controller 1. No TPA enabled. Level mode is with default settings since only acro mode is used. Level only activates as failsafe. |