rc:alfarc-fi-115
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
rc:alfarc-fi-115 [11.06.2021 17:22] vergo |
rc:alfarc-fi-115 [02.12.2023 01:46] (current) vergo [AlfaRC Fi-115 (2.5 inch)] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ====== AlfaRC Fi-115 (2.5 inch) ====== | ====== AlfaRC Fi-115 (2.5 inch) ====== | ||
| + | |||
| + | {{ : | ||
| ^ Specifications | ^ Specifications | ||
| Line 9: | Line 11: | ||
| | Antenna | Foxeer 5.8G Micro Lollipop | | | Antenna | Foxeer 5.8G Micro Lollipop | | ||
| | Motors | Happymodel EX1202.5 8000KV | | | Motors | Happymodel EX1202.5 8000KV | | ||
| - | | Props | HQProp T65MM (2-blade, T2.5x1.5x2) | | + | | Props | <del>HQProp T65MM (2-blade, T2.5x1.5x2)</ |
| | Camera | RunCam Racer Nano 2 with 1.8 mm lens | | | Camera | RunCam Racer Nano 2 with 1.8 mm lens | | ||
| - | | Battery | Turnigy nano-tech 2S 460 mAh 40C | | + | | Battery | <del>Turnigy nano-tech 2S 460 mAh 25-40C</ |
| ^ ^^ | ^ ^^ | ||
| - | | Weight | 78 g\\ 110 g (with battery) | | + | | Weight | 79 g \\ 110 g (with battery) \\ 92g (with RunCam Thumb, without battery) \\ 125g (with RunCam Thumb and battery) | |
| | M2M | 11.5 cm | | | M2M | 11.5 cm | | ||
| | Flight time | 4-5 minutes | | | Flight time | 4-5 minutes | | ||
| + | |||
| + | ===== Videos ===== | ||
| + | |||
| + | * with RunCam Thumb | ||
| + | * https:// | ||
| + | * https:// | ||
| + | * https:// | ||
| + | |||
| + | |||
| ===== Notes ===== | ===== Notes ===== | ||
| Line 24: | Line 35: | ||
| - The frame comes with plastic standoffs and rather short screws, consider replacing with aluminium standoffs and longer screws | - The frame comes with plastic standoffs and rather short screws, consider replacing with aluminium standoffs and longer screws | ||
| - A shrink wrap has been added over the RX+VTX board to keep the antenna connectors in place even if hit | - A shrink wrap has been added over the RX+VTX board to keep the antenna connectors in place even if hit | ||
| - | * This also has the benefit of fingers not touching the board components so easily when handling the frame | + | * This also has the benefit of fingers not touching the board components so easily when handling the frame |
| + | - The correct current sensor calibration value is somewhere between 290-300 | ||
| + | - ESCs have been updated with Bluejay ESC firmware for getting RPM telemetry | ||
| ===== Wiring ===== | ===== Wiring ===== | ||
| - | {{: | + | {{: |
| * FC+ESC and RX+VTX combinations simplify the wiring and space needed a lot | * FC+ESC and RX+VTX combinations simplify the wiring and space needed a lot | ||
| * The green wire in the provided Ghost Hybrid connector has the RX signal, blue can be removed | * The green wire in the provided Ghost Hybrid connector has the RX signal, blue can be removed | ||
rc/alfarc-fi-115.1623421324.txt.gz · Last modified: 11.06.2021 17:22 by vergo
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
