Differences

This shows you the differences between two versions of the page.

--- rc:alfarc-fi-115 [11.06.2021 15:43]
vergo created
+++ rc:alfarc-fi-115 [02.12.2023 01:46] (current)
vergo [AlfaRC Fi-115 (2.5 inch)]
@@ Line 2: / Line 2: @@
 ====== AlfaRC Fi-115 (2.5 inch) ======
+{{ :rc:files:fi115:alfarc_fi115.jpg?direct&400|}}
 ^  Specifications  ^^
-| Frame | AlfaRC Fi-115 (2.5 inch |
+| Frame | AlfaRC Fi-115 |
 | FC+ESC | JHEMCU GHF420AIO |
-| Motors | Happymodel EX1202.5 8000KV |
-| Props | HQProp T65MM (2-blade) |
 | RX+VTX | ImmersionRC Ghost Hybrid |
 | Antenna | Foxeer 5.8G Micro Lollipop |
+| Motors | Happymodel EX1202.5 8000KV |
+| Props | <del>HQProp T65MM (2-blade, T2.5x1.5x2)</del> \\ Gemfan Hurricane 2512-3 (3-blade, T2.5x1.2x3) |
 | Camera | RunCam Racer Nano 2 with 1.8 mm lens |
-| Battery | Turnigy nano-tech 2S 460 mAh 40C |
+| Battery | <del>Turnigy nano-tech 2S 460 mAh 25-40C</del> \\ CNHL MiniStar 2S 550 mAh 70-140C HV |
 ^ ^^
-| Weight | 78 g\\ 110 g (with battery) |
+| Weight | 79 g \\ 110 g (with battery) \\ 92g (with RunCam Thumb, without battery) \\ 125g (with RunCam Thumb and battery) |
 | M2M | 11.5 cm |
 | Flight time | 4-5 minutes |
+===== Videos =====
+  * with RunCam Thumb
+    * https://www.youtube.com/watch?v=tQnLrIdzKsA
+    * https://www.youtube.com/watch?v=5UbNBRfjiYU
+    * https://www.youtube.com/watch?v=WC9iwMm1IAU
+===== Notes =====
+  - RunCam Racer Nano 2 has far too much edge enhancement and color saturation by default at least when compared to older Swift models causing the image to look abnormal
+    * Most likely WDR has been the priority with the default settings as there's not much difference between light and shadow
+  - Edges of frame pieces should be sanded to avoid wear in wiring even if the outer edges have been pre-cut
+  - The frame comes with plastic standoffs and rather short screws, consider replacing with aluminium standoffs and longer screws
+  - A shrink wrap has been added over the RX+VTX board to keep the antenna connectors in place even if hit
+    * This also has the benefit of fingers not touching the board components so easily when handling the frame
+  - The correct current sensor calibration value is somewhere between 290-300
+  - ESCs have been updated with Bluejay ESC firmware for getting RPM telemetry
+===== Wiring =====
+{{:rc:files:fi115:alfarc_fi115_wiring.png?direct&450|}}
+  * FC+ESC and RX+VTX combinations simplify the wiring and space needed a lot
+  * The green wire in the provided Ghost Hybrid connector has the RX signal, blue can be removed

HumdiWiki

User Tools

Site Tools

Differences

Page Tools