This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
rc:lantian-l90 [05.05.2019 22:00] vergo |
rc:lantian-l90 [04.05.2021 21:31] vergo |
||
---|---|---|---|
Line 1: | Line 1: | ||
~~NOTOC~~ | ~~NOTOC~~ | ||
+ | |||
+ | < | ||
====== Lantian L90 ====== | ====== Lantian L90 ====== | ||
Line 10: | Line 12: | ||
| ESC | BLHELI_S V2 10A 4in1 ESC (from MyRCMart) | | | ESC | BLHELI_S V2 10A 4in1 ESC (from MyRCMart) | | ||
| Motors | Racerstar Racing Edition 1103 BR1103B 8000KV | | | Motors | Racerstar Racing Edition 1103 BR1103B 8000KV | | ||
- | | Props | Kingkong 1935 3-Blade Bullnose | | + | | Props | <del>Kingkong 1935 3-Blade Bullnose</ |
- | | Receiver | < | + | | Receiver | < |
| Camera | < | | Camera | < | ||
| VTX | Eachine VTX03 | | | VTX | Eachine VTX03 | | ||
Line 17: | Line 19: | ||
| Battery | Turnigy nano-tech 2S1P 460 mAh 25-40C | | | Battery | Turnigy nano-tech 2S1P 460 mAh 25-40C | | ||
^ ^^ | ^ ^^ | ||
- | | Weight | < | + | | Weight | < |
| M2M | 9 cm | | | M2M | 9 cm | | ||
| Flight time | 4-5 minutes | | | Flight time | 4-5 minutes | | ||
Line 33: | Line 35: | ||
- Edges of frame pieces should be sanded to avoid wear in wiring | - Edges of frame pieces should be sanded to avoid wear in wiring | ||
- | - Camera has been mounted with rubber O-rings due to lack of better mount | + | - <del>Camera has been mounted with rubber O-rings due to lack of better mount</ |
- Receiver antenna has been reinforced with a cable tie + heat shrink | - Receiver antenna has been reinforced with a cable tie + heat shrink | ||
- Don't attempt to flash the ESC firmware, 1 of 4 is likely to fail if done via FC, however changing settings is ok | - Don't attempt to flash the ESC firmware, 1 of 4 is likely to fail if done via FC, however changing settings is ok | ||
Line 42: | Line 44: | ||
- Older Kingkong 1935 props have a much tighter center hole which may not always fit the motors and push the shaft out of the motor instead when the prop is inserted | - Older Kingkong 1935 props have a much tighter center hole which may not always fit the motors and push the shaft out of the motor instead when the prop is inserted | ||
* More recent Kingkong 1935 props fix this issue with a slightly larger center hole, those can be identified from the center hub which isn't any longer fully flat | * More recent Kingkong 1935 props fix this issue with a slightly larger center hole, those can be identified from the center hub which isn't any longer fully flat | ||
- | - RunCam Micro Swift 2 will not fit with the default standoffs | + | - RunCam Micro Swift 2 will not fit with the default standoffs |
* With some plastic removal, it's possible to fit the camera using a custom mount while still using the default standoffs and having possibility to get some angle to the camera | * With some plastic removal, it's possible to fit the camera using a custom mount while still using the default standoffs and having possibility to get some angle to the camera | ||
* Only the height is a restricting factor | * Only the height is a restricting factor | ||
+ | - FrSky XM replaced with FrSky XM+ due to [[https:// | ||
===== Wiring ===== | ===== Wiring ===== |